
Frequently Asked Questions
Flashing & Moisture Management
What does through-wall flashing do?
Water that gets into a brick veneer wall drains down the cavity between the brick and the backup wall. Through-wall flashing collects that water and directs it out through the weep holes before it reaches structural materials. To do its job, it should extend completely through the veneer wall assembly. Our GENFLASH® is a flexible, primerless membrane for masonry through-wall flashing.
Which flashing products does 3GEN carry?
It depends on the material you need. GENFLASH is our flexible, primerless membrane. For stainless, there’s GENFLASH SS in Type 304 stainless steel and GENFLASH SS SA, its self-adhered version. For copper, you can choose GENFLASH Copper or the self-adhered GENFLASH Copper SA. We also offer GENFLASH Primer, which improves adhesion of flashing membranes, and GENFLASH Sealant for sealing masonry flashing.
Where does a drip edge go, and what is it for?
The drip edge sits under the flashing and helps channel moisture out of the cavity wall. Ours is Type 304 stainless steel, 26 gauge, and comes in 8 ft lengths, either 1.5″ or 3″ wide, with a 3/8″ hemmed edge at 45 degrees. If you need to turn a corner, we also make corner sections, 3″ wide x 8″ x 8″ long.
What is the purpose of a cell vent?
A cell vent gives the cavity wall drainage and airflow. The 3GEN Cell Vent is made of flexible, UV-resistant polypropylene and comes in two sizes: Standard (3/8″ x 2 1/2″ high x 3 3/8″ deep) and Jumbo (3/8″ x 3 1/2″ high x 3 3/8″ deep). You can pick from Almond, Black, Buff, Cocoa, Clear, Gray or White.
Why would I need a termination bar?
A termination bar mechanically secures the top of surface-mounted flashing to the substrate, and ours is compatible with all flashing products. Type F (Flat) comes in Type 304 stainless steel or aluminum, sized 1/8″ x 1″ x 8 ft. Type L (Lip) has a 45-degree lip that allows for proper placement of sealant, and comes in aluminum (14 gauge x 1″ x 8 ft) or Type 304 stainless steel (26 gauge x 1 1/2″ x 8 ft). Both have 9/32″ holes spaced 8″ on center.
Control Joints
What is a control joint, and why do concrete block walls need one?
Concrete masonry walls can experience shrinkage and movement due to temperature changes and other environmental conditions. Control joints help accommodate that movement and reduce the potential for uncontrolled cracking.
Which control joint profiles are available?
You can choose from four: CJ-+, CJ-T, CJ-8 and CJ-12, in PVC and rubber options. Check the submittal sheet on the Control Joint page for details.
Veneer Anchors & Ties
How do you anchor brick veneer to the backup wall?
Our H-10 and H-13 veneer anchors work with metal stud, wood stud, concrete block or poured concrete backup. Recommended spacing is 16″ on center. If you are working with metal studs, fasten the anchors with our TEK Screws. Both the H-10 and the H-13 meet TMS 402/602 and ACI/ASCE 530.
Will your veneer anchors work with insulation?
Yes. The H-13-H, H-13-V and H-13 Washer can be used with either rigid or spray foam insulation.
What is the Triangle for?
The Triangle pairs with our H-10 and H-13 veneer anchors. It is made from 3/16″ wire, and you can get it hot-dip galvanized or in Type 304 stainless steel. When it is used with the H-10, recommended spacing is 16″ on center.
Do you have veneer anchors for seismic applications?
Yes. Our seismic line includes the H-10 Seismic, H-13-H Seismic, H-13-V Seismic and Barrel Anchor Metal Stud Seismic. Depending on the anchor, it comes with a plastic clip, a welded clip or a seismic triangle. The H-13-V can also be upgraded for seismic use with a plastic clip and continuous wire. Product selection should be confirmed by the project’s design professional based on project-specific conditions and applicable codes.
What finishes can I order?
Finish options vary by product. The H-10 and H-13-H are available hot-dip galvanized or in Type 304 stainless steel, while the H-13-V and H-13 Washer are hot-dip galvanized. Check the submittal sheet on each product page for details.
Ordering, Quotes & Documents
Where do I find submittal sheets, SDS and LEED documents?
Product documentation, including submittal sheets, SDS and LEED documents, is available in the Documents & Downloads section of each product page. Select your product to find the technical resources and documentation available for download.
How can I get a quote?
Reach out through our Contact Us page or give us a call at 1-800-556-5785.
How do I find my 3GEN sales rep?
Our Find A Sales Rep tool will point you to the right person. Search by state or zip code, then click a map marker to see your rep’s contact information. You can also call us at 1-800-556-5785.









































































